C46 fi code. GSXR 600 K7 - F1 error code C46

Oh no, did yo she pull your short hairs out the harness too? Yes, I pulled the black wire with the brown stripe from slot 30 5th one in on the black connector to the ECU. New posts. After doing the 'paper clip' trick to get it in dealer mode, the actual error code was C46, which is the Exhaust control valve actuator not working correctly, which is what I thought as the bike wouldn't rev out above 6K I assumed the butterfly was only half open or so and not allowing the gases to escape properly. If you have an account, sign in now to post with your account.

 

Your Problem Is The.You must be logged in to rate posts.

 

farmasiuyelik.online › › GSX-R/I also hear a loud pop from my exhaust when I am revving to 8K and letting off throttle with ease.

 

I'm getting FI warning and shop say's it's C46 which I understand is exhaust valve actuator. I read several posts that said you can cut the.It's the K8 that requires a cut and shut.

 

farmasiuyelik.online › watch.It'll squeak at the same time the fuel pump primes

 

I just put a full exhaust system on my 06 gsxr and I need to know what wires to cut on the servo and the ECM to clear error code R.Noticed a few months ago that the Gixxer would flash up FI on the dash and the oil light came on.

 

06 nine. used paper clip (special tool) and c46 was displayed, the hash mark beside it did not respond to throttle. How do I repair c46 code.Wiring Remove the seat.

 

I'm running a full Lextek system and the F1 - C46 exhaust servo code has just appeared. I'm not mechanically minded but given it has the.Guess I really have to take her to a shop, right?

 

F1 code after TPS: C14 & C42 codes - how do I clear these? Suzuki GSXS Troubleshooting. 17; 3K; DennisBergkamp · updated 6 mo ago.Yes, I pulled the black wire with the brown stripe from slot 30 5th one in on the black connector to the ECU.

 

If you look at the exhaust there will be a valve operated by 2 cables. This should open and then close when you turn the ignition on. If it.Pull out both harnesses, the grey one is not needed but pulling it out makes the black harness easier to work with.

 

I don't know much about the C46 code, so I googled "suzuki dealer mode code c46". Not sure if it is the same thing, but there are a few.No wonder the code was C

 

Suzuki GSX-R Service Manual: DTC “c46” (ph/l or p): excv actuator circuit malfunction · Loose or poor contacts on the excva or ecm coupler .I also hear a loud pop from my exhaust when I am revving to 8K and letting off throttle with ease.

 

never had any issues with the FI lights before putting in storage, but when we crank the bike it gives the FI light with error code CThen i disconnected the jumper cable and now my F1 light has dissappeared.

 

forum? I pulled the wire on the harness (black with brown stripe) that I thought was for the set valve but I'm still getting C46 (exhaust valve).Saxaboom 3, posts months.

 

the most detailed instructions on how to remove the valve and be free of the dreaded fi light!this is the tutorial i used back in janua.Would any of you tech guys be kind enough to help me check the codes?

 

MOTORCYCLE DIVISION. 4-STROKE SERVICE BULLETIN GS/GSX/GSX-R/GSF NO. A DATE: 3/26/ SUBJECT: MODEL: C46 TROUBLESHOOTING AN INTERMITTENT FI CODE.Please be fair in your ratings!

 

After doing the 'paper clip' trick to get it in dealer mode, the actual error code was C46, which is the Exhaust control valve actuator not.Back to top.

 

IP CAMERA IPC-C46 Wi-Fi - Mpx mm DAHUA The cameras of the Dahua Consumer series have been designed with special care to simplify the configuration and.Stock clearance.

 

c suzuki logo. gsxr logo. MALFUNCTION CODE In this case, the code c24 or C25 or C26 or c27 is indicated. c28, Secondary throttle valve actuator.Hi, I installed a power commandor a while back.

 

I started the bike, revved it a bit and the code was C Now what? Its an error with exhaust control valve actuator. Guess I really have to.Log in Register.

 

This problem happened about ten days ago when I was going home on DVP northbound.

 

These ecu's are fairly fragile and maybe shorted out a little?

 

Back to top.

 

Rather than removing the entire rear fairing, I choose to remove only the side that I needed to in order to get to the servo.

 

View previous topic : View next topic.

 

Back to top.

 

Search in descriptions Advanced search.

 

Remove cross bracket.

 

Posted June 30,

 

I'll be installing a custom exhaust which i've bought off ebay so maybe the fault may go away?

 

These ecu's are fairly fragile and maybe shorted out a little?

 

I always use 3M electrical tape.

 

Aslo did u do the pair valve mod too?

 

Do not use el-cheapo tape as it will not hold for long.

 

Hey fella.

 

ONVIF :.

 

Search Advanced search….Forum C46 fi code